Highlights • Optical Coherence Tomography shows real-time 3D internal defects in composites. • Tested light-cured bulk-filled materials mainly showed inner voids and cracks. • New flowable bulk-fill material achieved sound…
Abstract Objective To evaluate the influence of the addition of functionalized and non-functionalized TiO 2 nanostructures on properties of a resin composite. Methods TiO 2 nanostructures were synthesized and functionalized,…
Highlights • Cusp angle of the dental crown is directly proportional to the load-carrying capacity. • Failure always initiated at the centre of the midline of the occlusal surface. •…
Highlights • Development of a dynamic mechanical analysis method to assess bulk viscoelastic behavior of dentin • Protein destabilization accelerates H-bond breakage in biomodified dentin matrix • Key PAC structural…
Graphical abstract Highlights • Antimicrobial and antibiofilm thymol (TOH) coating on titanium (Ti) was developed. • An easy one step deep-coating method in a TOH-containing solution was used. • The…
Highlights • Fibers improve mechanical properties of a resin modified glass ionomer cement (RMGIC). • Mechanical properties with RMGIC matrix are improved over GIC matrix. • Braided long fibers give…
Highlights • Different failure modes were considered as competing risks in statistical analyses. • Conventional failure mode non-distinguishing models may underestimate bond strength. • Competing risk models could estimate bond…
The challenges faced by researchers in dental materials are many and varied. In particular, mechanical testing has many constraints and potential interferences that can, if not addressed, at best vitiate,…
Highlights • A motorized device was developed to simulate movements of light curing unit. • Different cements, LCUs and exposure protocols can lead to different in vitro results. • Delivering…
Highlights • Monolithic bridges from three zirconia grades were subjected to aging/loading. • Aging and loading did not affect the fracture load of translucent zirconia bridges. • Transformability correlated with…
Graphical abstract Abstract Objective To investigate the metal ion release, surface roughness and cytoxicity for Co–Cr alloys produced by different manufacturing techniques before and after heat treatment. In addition, to…
Highlights • 0.1% EGCG/DWB and 1%EGCG/DWB preserved dentin bond strength and reduced interfacial nanoleakage. • 1%EGCG/DWB inhibited S. mutans growth and biofilm formation along the dentin–adhesive interface. • Adjunctive application…
Graphical abstract Highlights • The properties and performance of porous implants were examined by in vitro mechanical test, in vivo micro-CT and ex vivo pull out test. • The results…
Highlights • The tested materials showed different amount of eluted monomers. • Printing device had significant impact on monomer release. • Monomer release is comparable to conventional dental composite materials….
Highlights • Scanning mode nanoDMA was used to evaluate the dynamic mechanical properties of intertubular and peritubular dentin. • The intertubular dentin from the old donor teeth exhibited higher storage…
Highlights • This is the first long-term clinical study evaluating the first commercial universal adhesive. • The etch-and-rinse (moist or dry) strategy showed better clinical behavior than the self-etch strategy….
Highlights • The composite showed enhanced cell proliferation rate when compared to Y-TZP. • Addition of 12.5% of titania to Y-TZP resulted in formation of more mineralization nodules compared to…
Abstract Objective The aim of the present study was to evaluate the effect of quercetin on the acid resistance of human dentin through both laboratory and clinical studies. Methods Two…
Highlights • Wear tests were conducted on a multilayer 5Y/4Y-PSZ and a monolithic 3Y-TZP. • Wear volume loss and depth were greater in 5Y/4Y-PSZ than in 3Y-TZP. • Worn surface…
Highlights • Ca/P-PILP was synthesized at high Ca2+ concentration without precipitation. • Electron Probe Micro Analyzer was used to investigate element contents. • Artificial caries dentin lesion could be biomimetic…
