Abstract In this case series, we present six cases with the initial complaint of pain and/or progressive unilateral pre-auricular swelling. All patients presented at our Department of Oral and Maxillofacial…
Abstract In this case report a cleft patient with tentative diagnosis of craniofrontonasal dysplasia who was treated with a ‘chin wing’ osteotomy is described. Alternative treatment options are discussed. A…
Abstract Objectives Selective caries removal (SCR) is recommended over non-selective removal for managing deep carious lesions to avoid pulp exposure and maintain pulp vitality. During SCR, residual carious dentin is…
Highlights •High-challenge biofilm model was used against ZnO-loaded adhesives. •ZnO-loaded adhesives were tested against mature saliva-derived microcosm biofilm. •Group with 7.5 wt.% of ZnO decreased mature biofilm formation on adhesives….
Abstract Objective The purpose of this study was to assess the effects of an experimental primer containing acetone solution and a sulfur-containing functional monomer, 10-methacryloyloxydecyl-(2-thiohydantoin-4-yl)propionate (MDTHP), on the bonds between…
Abstract Objective Despite the increased use of monolithic crowns, their performance has yet to be determined when the minimal tooth preparation (MTP) principle is considered. The goal of this study…
Highlights • HF followed by silane and self-etching ceramic primer promoted higher flexure strength. • Sandblasting with Al 2 O 3 and silicatization produced damages to all ceramics evaluated. •…
Graphical abstract Highlights • High probability of survival was observed even for 0.5 mm restorations. • Models with thinner restorations accumulated more stress in the structures. • Resin-matrix ceramic materials…
Graphical abstract Highlights • Digital technology in prosthetic practice uses milled PMMA discs. • DMA and Brillouin spectroscopy are innovative techniques in dentistry. • Tested materials exhibit better mechanical properties…
Highlights • Anisotropic corrosion resistance was found in SLM-processed Co-Cr alloys. • Selective corrosion occurred along the molten pool boundaries (MPBs). • The MPB area was dependent on the building…
Abstract Objectives The aim of this study was to investigate dentin bonding durability of different etch-and-rinse (ER) adhesive systems under fatigue stress and to compare morphological features of resin/dentin interfaces…
Abstract Objective Micro-nano scale surface modification of Ti-6Al-4V was investigated through the fascinated modern fiber engraving laser method. The process was performed at a high laser speed of 2000 mm/s,…
Abstract Objective The angiogenic differentiation of dental pulp stem cells (DPSCs) is important for tissue homeostasis and wound healing. In this study the influence of 2-hydroxyethyl methacrylate (HEMA) on angiogenic…
Abstract Objective The aim is to recommend a fast and cost-effective screening procedure for UK/SA SARS-CoV-2 variants in a routing diagnostic setting. Methods A rapid procedure using qPCR is described…
Highlights • Resin-matrix ceramics systems demonstrated high reliability at functional loads. • Resin-matrix ceramic fracture, chipping or catastrophic, is the chief failure mode. • Cracks originated by quasiplastic deformation under…
Abstract Objective The airborne-particle abrasion of zirconia with alumina particle (APA) has been reported to result in the durable bonding of appropriate adhesive luting systems. However, whether a delay between…
Highlights • Silanization of halloysite nanotubes was not detrimental to the mechanical properties of the resin-based material. • Silanization of halloysite nanotubes improved the antimicrobial activity of the chlorhexidine. •…
Graphical abstract Abstract Objective Viruses on environmental surfaces, in saliva and other body fluids represent risk of contamination for general population and healthcare professionals. The development of vaccines and medicines…
Highlights • Reduced functional loads affect interradicular (IR) bone. • Biomechanics in situ with X-ray and DVC can identify differences in functional adaptation of the DAJ. • Form- and material-related…
Highlights • Essential work of fracture (EWF) was used to determine the essential work of fracture of a fiber-reinforced dental composite. • The thickness of conventional composites covering the fiber-reinforced…
