6: Developing Occlusal Schemes for Complete Dentures

Chapter 6

Developing Occlusal Schemes for Complete Dentures

Aim

The aim of this chapter is to discuss the influence of occlusion on the outcome of complete denture therapy.

Outcome

At the end of this chapter, the clinician should be aware that requirements for occlusion in edentulous patients are substantially different from dentate patients. Occlusal schemes for edentulous patients must be developed to facilitate stability and retention of complete dentures. The clinician should be aware that there are a number of occlusal schemes described and the scheme used will influence the choice of posterior teeth. The role of articulators in setting up posterior teeth should also be understood.

Occlusal Schemes – Why Bother?

In Chapter 3, the relationship between retention, stability and support was outlined. A major factor that influences retention is the occlusion of the dentures. The clinician should aim for even, balancing contacts on as many denture teeth as possible during excursive movements. In a dentate patient, the ideal occlusion would be canine guided in excursive movements. If this scheme were incorporated into a complete denture, then the occlusal forces would be directed unilaterally and would overcome forces of retention. The degree of horizontal and vertical (overjet and overbite) overlap of teeth is also relevant. In a patient with a skeletal Class 2 relationship, it may be possible to reduce the amount of horizontal overlap and thus increase the number of occlusal contacts. It is also important to avoid too much anterior overbite, and an edge-to-edge relationship with minimal overbite is the most favourable arrangement (Fig 6-1). However, in some cases, this may affect speech or lead to unsatisfactory appearance. There has been much debate in the scientific literature regarding the impact of occlusion on alveolar resorption. There is little evidence to support the notion that alveolar bone resorption is accelerated by failure to provide balanced articulation. Consequently, occlusal schemes for complete dentures should be designed to facilitate:

  • denture retention

  • chewing.

QE12_Allen_fig070.jpg

Fig 6-1 Preferred incisal relationship for stability and retention. Note the minimal amount of overlap.

The emphasis is on the word designed as most factors are under the clinician’s control.

What Factors Influence Occlusion?

Hanau described five factors which must be considered when developing the posterior occlusion. These are (a) incisal guidance angle; (b) condylar guidance angle; (c) orientation of the occlusal plane; (d) cusp angulation; and (e) slope of the compensating curve. In terms of complete denture construction, with the exception of the condylar guidance angle, all of these factors are under the clinician’s control.

The incisal guidance angle of the articulator can be set at zero and the teeth placed with minimal overlap. This will decrease or even eliminate incisal guidance during excursive movements, thus reducing tipping forces on the maxillary denture. If cosmetic requirements dictate that a greater degree of overlap between the anterior teeth is required, then the incisal guidance must be greater than zero. As a general principle, when the incisal guidance angle increases, the cusp angle of posterior teeth should also increase to maintain balanced articulation. Once again, this will influence the choice of articula-tor and a semi-adjustable articulator is indicated when incisal guidance angle is increased.

The condylar guidance angle cannot be altered by the clinician as this is related to the path of movement of the condyle in the glenoid fossa during excursive movements of the mandible. It cannot be represented by non-anatomical articulators, and is represented to a limited extent on semi-adjustable articulators.

As described in Chapter 4, the orientation of the occlusal plane of complete dentures is dictated by reference to external landmarks such as the interpupillary and the alatragal lines. If the orientation of the occlusal plane is incorrect, then this will impact upon appearance and possibly cause occlusal interferences. The orientation of the plane is deter/>

Only gold members can continue reading. Log In or Register to continue

Stay updated, free dental videos. Join our Telegram channel

Jan 17, 2015 | Posted by in Prosthodontics | Comments Off on 6: Developing Occlusal Schemes for Complete Dentures

VIDEdental - Online dental courses

Get VIDEdental app for watching clinical videos