6 Bar Attachments

6

Bar Attachments

Hamid Shafie
James Ellison

BAR MATERIALS

Bar attachments can be prefabricated type IV gold like the original 1.6mm Dolder Bar. Prefabricated type IV gold bars should be soldered to the abutments with a low fusing solder. The other types of bars come in castable pre-milled plastic patterns. These bars are available in 0, 2, and 4 degrees for telescopic milled restorations. The bar castings should only be made with hard alloys. A minimum Vickers hardness of 200 and at least 95,000psi ultimate tensile strength is required. Non-precious alloys are contraindicated for implant reconstruction.

Examples of Castable Bars

  • Round bar
  • Plastic Dolder Bar
  • I bar
  • EDS bar
  • Hader Bar

Bar clips or riders are available in different materials and configurations. The metal clips/riders are fully adjustable. Plastic Hader/EDS clips are non-adjustable, but they can easily be replaced at chair side. Use of a metal housing with Hader/EDS plastic clips is strongly recommended.

Classification of Bar Attachments Based on Cross-Sectional Shapes

FIGURE 6.1.

image

FIGURE 6.2.

image

FIGURE 6.3.

image

FIGURE 6.4.

image

Classification of Bars Based on the Nature of Their Resiliency

  • Bar joints (resilient) provide vertical and/or hinge resiliency (Figure 6.5)

FIGURE 6.5.

image

FIGURE 6.6.

image

Factors that Influence the Flexibility of the Bar

  • Length of the bar between the two implants
  • Number of implants that support the bar
  • Height of the bar
  • Physical properties of the alloy
  • Magnitude of the masticatory loads

FUNDAMENTALS OF BAR ARRANGEMENT

As a general rule if a single bar is being utilized, the ideal length should be 20–22mm to accommodate two clips/riders. This means the center of the implants should be 24–26mm apart if standard diameter 4mm implants are being used (Figure 6.7 and 6.8).

FIGURE 6.7.

image

FIGURE 6.8.

image

If the two implants are too close, the short bar cannot provide enough retention and stability for the overdenture (Figure 6.9).

FIGURE 6.9.

image

This distance, however, depends on following conditions:

  • Size and curvature of the mandibular arch
  • Type of attachment assembly

If the implants are placed too far distally, a straight-line bar will interfere with the tongue space and create problems in fabricating the prosthesis, also it will be at risk of bending (Figure 6.10 and 6.11).

If the bar has been positioned diagonally, it will not allow friction free anterior hinge movement of the prosthesis. This condition creates excessive torsional loading on the supporting implants (Figure 6.12).

FIGURE 6.10.

image

FIGURE 6.11.

image

FIGURE 6.12.

image

As a general rule the bar should be perpendicular to the line that bisects the angle formed by the two posterior mandibular arch segments (Figure 6.13).

FIGURE 6.13.

image

Vertical Relationship of the Bar to the Alveolar Ridge

  • Wide Gap: There is 2mm or more between the bottom of the bar and the soft tissue (Figure 6.14). This distance allows easy passage of saliva and food particles as well as cleaning tools. Hygiene maintenance in this situation is very easy.

FIGURE 6.14.

image
  • Small Gap: There is 1mm or less between the bottom of the bar and the soft tissue (Figure 6.15). This distance will cause plaque and calculus accumulation and it would be very difficult to perform oral hygiene maintenance.

FIGURE 6.15.

image
  • Compression of the Mucosa by the Bar: This causes hyperplasia of the gum (Figure 6.16). It is impossible to clean underneath the bar. The bar should be replaced or modified to solve this problem.

FIGURE 6.16.

image

Sagittal Relationship of the Bar to the Alveolar Ridge

The bar should be positioned directly above the crest of the ridge (Figure 6.17). This position makes it easy to clean the bar and fabricate the prosthesis above the bar.

FIGURE 6.17.

image

If the bar is positioned lingual to the crest of the ridge, it will interfere with tongue space and its function and the patient’s speech (Figure 6.18). This problem is a common situation in patients with a narrow and pointed alveolar ridge. One way to prevent this situation is to relocate the bar further anteriorly. Another solution is to use individual attachments.

FIGURE 6.18.

image

If the bar is positioned labial to the crest of the ridge, it will interfere with lip support (Figure 6.19). Both of these scenarios will make fabrication of the prosthesis very difficult.

FIGURE 6.19.

image

Sagittal Relationship of the Bar to the Hinge Axis

It would be ideal if the anterior bar in the edentulous mandible were parallel to the hinge axis. However, this relationship is another reference for better positioning of the bar and this orientation can’t be achieved in every case. This rule has been followed by many clinicians, but no studies have supported this claim. The long term study (5–15 years) by Oetterli, Kiener and Mericske-Stern analyzed the influence of placing the bar parallel to the hinge axis on peri-implant parameters, including the clinical attachment level. The outcome as far as the type of retention, splinted versus unsplinted, was also assessed. No significant correlations were found.

Sometimes the anatomical shape of the alveolar ridge will not allow the surgeon to position the implants with the bar parallel to the hinge axis (Figure 6.20 and 6.21). In this situation, the lab technician and restorative doctor can modify the bar design to achieve this goal.

FIGURE 6.20.

image

FIGURE 6.21.

image

Anterior-Posterior Distance Rule

The anterior-posterior distance rule is good for determining the distal cantilever extension of the bar or distal extension of the hybrid (fixed detachable) prosthesis from the most posterior implants.

  • Draw a line through the center of the most posterior implants on each side of the arch (Figure 6.22).
  • Draw another line through the center of the most anterior implants on each side of the arch.
  • The distance between these two lines is the Anterior-Posterior spread (A–P distance).
  • Generally, the distal cantilever should not exceed more than half of the Anterior–Posterior distance.

FIGURE 6.22.

image

If the patient has a small mandible, with limited room for four implants, putting the distal implants as far back as possible to the mental nerve can enhance the A–P distance. In addition, the anterior implants should be brought forward as far as possible. These steps will improve the A–P distance to ensure that the basic biomechanical rules are not violated. The maximum cantilever in these cases is generally 8–12mm.

If the patient has a square arch, the implants will be in a straight line in the anterior segment of the mandible. In this situation, any cantilever design must be avoided since the A–P distance will be non-existent or significantly reduced. Resilient bar assemblies are suggested for these patients. The prosthesis should be implant and tissue born so that the buccal shelf and retromolar pad will receive a share of the occlusal load.

To minimize the compressive load on the bar, the denture base can be relieved in the area over the distal extensions.

Guidelines for Denture Base Extension

  • Mainly Tissue Supported Implant Overdenture: The borders of the overdenture in the anterior area should not extend to the end of the sulcus. There should be minimum extension in the anterior region but maximum extension in stress bearing areas such as buccal shelves. The denture base should extend distally onto the retromolar pads and lingually onto the mylohyoid ridge.
  • Tissue-Implant-Supported Overdenture: The borders of the overdenture are significantly shorter than conventional dentures; however, they can’t be eliminated since this type of prosthesis is still partly tissue supported.
  • Fully Implant-Supported Overdenture: Since the prosthesis is completely implant born, flanges can be eliminated.

HADER BAR

In 1973, Helmut Hader, master technician and dental manufacturer, developed a unique attachment system that even today is mainly known in the USA as Hader Bar and Hader Vertical. The Hader Bar is a semi-precision bar attachment that provides hinge movement as long as a single Hader Bar has been utilized in an attachment assembly design. The function of this bar is based on the mechanical snap retention concept (Figures 6.23 and 6.24).

FIGURE 6.23.

image

Three color-coded clips/riders are available with three retentive strengths. In order from the least to most retentive, they are white, yellow, and red. Use of a metal housing with the Hader plastic clips/riders is strongly recommended. In addition to plastic clips/riders, the option of adjustable gold alloy clips/riders is available (Figures 6.25 and 6.26).

FIGURE 6.24.

image

FIGURE 6.25.

image

FIGURE 6.26.

image

Fabrication Procedures for a Castable Hader Bar Attachment with Plastic Clips/Riders

1. Choose matching pick-up impression copings based on the implant type and diameter.
2. Make a full arch pick-up impression utilizing a rigid impression material such as polyether.
3. Fabricate the master cast with soft tissue model.
4. Choose matching gold base non-hex plastic UCLA abutments.
5. Adjust the length of the plastic bar based on the distance between the UCLA abutments and the shape of the alveolar ridge.
6. Connect the plastic bar to the UCLA abutments with wax.
7. Sprue the bar and UCLA abutments. The sprues should always be placed on the connecting points of the bar.
8. Complete the casting steps.
  Note: The burnout for plastic components requires two stages. First, raise the temperature slowly to 600°F (316°C) and hold for 30 minutes. This assures a clean and complete burnout of the plastic piece. Second, complete the burnout procedure by following the instructions of the alloy manufacturer.
9. Finish and polish the casting.
Note: Do not grind the round bar with stones, burs, or rubber wheels. Grinding reduces the bar diameter and alters the fit and retention of the clips/riders. Finish and polish with polishing compound or with Tripoli and rouge.
10. Try the bar in the mouth by using the Sheffield test. (Refer to Chapter 7.)
  Note: If a removable die model was used for fabricating the bar, or if the bar has to be cut and soldered, then a new impression should be made picking up the bar and retainers. A new, solid master model is fabricated from this impression.
11. Insert the polished bar on the solid master cast. Snap plastic clips/riders on the bar. Insert as many clips/riders on the bar as space allows, which will provide space for additional clips/riders to be inserted to increase retention if necessary. Block out the undercuts of the bar and over the abutments. Do not block out the retentive undercuts of the clips/riders.
  Note: Recommended block-out materials are Rubber Sep. Sterngold order #812045 and Litebloc UV–Bredent order #52000980.
12. In order to fabricate a duplicate cast for denture processing, make an impression of the master cast with the undercuts blocked out on the screwed bar and clips/riders that are snapped on the bar.
13. Insert laboratory clips/riders into the impression in exactly the same position as the imprints of the actual clips/riders and pour the impression. The laboratory clips/riders will be held in the proper position in the duplicate cast by the extensions of the riders in the stone.
  Note: Do not try to shorten the extension of the laboratory riders/clips and place them on the bar. Shortening the extension will cause improper fit of the laboratory clips/riders on the bar, which will create larger retention spaces in the denture base. In this situation, the final clips/riders will not be completely stable in the denture base. When the patient removes the overdenture, the clips/riders will tend to be pulled out of the denture base and remain on the bar.
  Note: If metal housings are used, slide them onto the laboratory clips/riders from the side of the clip after fabrication of the duplicate cast. Do not snap the metal housings on the laboratory riders/clips from the occlusal direction, which could deform the housings and cause the final riders/clips to pull out of the denture.
14. Try the denture teeth setup in the mouth. Send the teeth back to the lab for processing.
15. Insert the prosthesis on the duplicate cast and process it with the technique of choice.
16. Deflask the prosthesis. Remove all of the stone and then remove the laboratory clips/ riders with pliers or a hemostat. Finish and polish the denture.
17. Insert actual clips/riders in their position in the denture base by using a special seating tool, which has been supplied in the attachment kit. Press the clips/riders into the prepared receptacles in the acrylic denture base or into the metal housings, which are already positioned in the denture base. There should be a snap when the clips/riders are pushed into position. The clips/riders are easily seated and can be easily replaced. The special shape of the receptacle in the acrylic denture base or metal housing provides secure retention of the clips/riders, while providing leeway space in the labiolingual direction to allow the clips/riders some flex during insertion or removal of the prosthesis.

Fabrication Procedures for a Castable Hader Bar Attachment with Gold Alloy Clips/Riders

1. Choose the desirable gauge of the/>

Only gold members can continue reading. Log In or Register to continue

Stay updated, free dental videos. Join our Telegram channel

Jan 5, 2015 | Posted by in Implantology | Comments Off on 6 Bar Attachments

VIDEdental - Online dental courses

Get VIDEdental app for watching clinical videos